inlet manifold

1. A new casting technology for inlet manifold in tilt casting machine for gravity die casting was described.
   介绍了在可倾式金属型浇注机上制造进气歧管的铸造新工艺。
2. The structural characteristics of inlet manifold with dispersive hotspot for Ford car were analyzed.
   分析了福特电喷进气歧管热节分散的结构特点。
3. Aluminum Alloy Inlet Manifold of Micro-car in Metal Mold Casting
   铝合金进气歧管铸件的金属型铸造
4. Effects of inlet manifold dimensions on volumetric efficiency of engines
   进气管结构参数对柴油机充气效率的影响
5. Effect of Inlet Manifold Construction and Dimension on Volumetric Efficiency and Performance of Four Stroke High Speed Multi-cylinder Truck Diesel Engine
   进气管结构参数对四冲程多缸高速车用柴油机充气效率及性能的影响
6. Application of CAD/ CAE of Casting Process to Inlet Manifold Design
   铸造工艺CAD/CAE在进气管设计中的应用
7. Then, gas field of fuel cell stack inlet air manifold and cathode flow field are modeled by computational fluid dynamics software Fluent.
   然后，利用计算流体动力学软件Fluent对燃料电池堆进气箱和阴极流场进行了气场模拟。
8. Inlet Manifold for Ford Car in Permanent Mold Casting
   福特电喷进气歧管金属型重力铸造工艺
9. The effects of intake chamber volume, diameter and length of inlet duct and inlet manifold on volumetric efficiency were analyzed.
   分析了进气总管和进气支管的管长、管径以及进气腔容积对充气系数的影响规律。
10. Research on the Muffling Characteristics of the Serial-parallel Inlet and Exhaust Manifold of Motor Vehicle Engine
    汽车发动机串并联进排气系统消声特性的研究
11. Cause Analysis of Primary Reformer Inlet Manifold Damage
    一段炉下集气管损坏原因分析
12. In this paper, a FVM-TVD method for simulation of one-dimensional unsteady flow in inlet and exhaust manifold of ICE has been constructed.
    介绍了进排气系统一维非定常流动的FVM-TVD法（总残差减少的有限体积法）。
13. The situation of mould manufacturing for inlet manifold in rapid prototyping and investment casting was introduced.
    介绍了以快速原型技术和精密铸造技术进行进气歧管铸造模具制造的情况。
14. An Analysis of the Air Flowing Coefficient and Swirl Intensity of Helical Inlet Manifold in Diesel Engines
    Air（初三适用）柴油机螺旋进气道充气系数与涡流强度的分析
15. Mould Manufacturing for Inlet Manifold Based on Rapid Prototyping
    基于快速原型技术的进气歧管模具制造
16. Flow Field Analysis and Structure Optimization of PEM Fuel Cell Air Inlet Manifold
    PEM燃料电池进气箱的流场分析与结构优化
17. Acoustic transferring matrix method and sound wave finite element analysis method have been employed respectively to perform calculation for the muffling characteristics of the serial-parallel piping of the inlet and exhaust manifold of motor vehicle engine, and meanwhile physical measurement has been carried out for the engine.
    对汽车发动机进排气系统的串、并联管道系统的消声特性，分别用声学传递矩阵方法和声波有限元分析方法进行了理论计算，同时对发动机进行了实测。
18. 3-D flow field analysis and numerical simulation in fuel cell air inlet manifold
    燃料电池气体分配箱三维流场分析与数值模拟
19. The full process from three dimensional geometrical modeling to the generation of moulding tools can be better realized through the application of CAD/ CAE system of casting process to inlet manifold design for the motor.
    将铸造工艺CAD/CAE系统应用到汽车进气管零件的设计中，能够较完整地完成从三维实体造型到最后生成模具的全过程。
20. The simulation results of inlet air manifold show that the uniformity of the velocity at outlet of the manifold are improved by using the appropriate bell-mouthed inlet and clipper-built baffle, and inlet pressure needed of the manifold decrease.
    对进气箱的模拟结果表明，采用扩压型进口加流线型挡块的方案可以提高出口速度的均匀性，同时降低了进气箱入口所需的气体压力。
21. Using the universal finite element software structure strength analysis of manifold inlet manifold structure strength, modal and noise is analyzed and calculated.
    利用通用有限元软件对进气歧管结构强度、模态和噪声进行了分析计算，为进气歧管三维结构优化提供理论依据。

noun

1. manifold that carries vaporized fuel from the carburetor to the inlet valves of the cylinders